Fogarty's Home Services Before & After Photos

This homeowner in East Hampton, CT called us stating that he had high radon levels. When his home was tested, he had a radon level of 7 pCi/L on average. He had a long history of readings for his radon level that he wanted to review. He was the original owner of the home, as he had built it himself. He wanted his levels lowered so that he could feel more confident in his home.

We had the perfect solution for this customer! We installed a radon mitigation system in his home. We identified the specific space where the mitigation system should be installed. After that, we drilled a hole in the floor as well as a hole in the wall for the exterior penetration. We put together the pipes, starting in the floor, and built it out through the exterior penetration to the outside. We secured the pipes to the wall, and then installed the manometer onto the pipe. (A manometer measures the pressure of the radon gas in the system, indicating whether or not the system is functioning). We then went outside to continue building out the system. We installed the fan and continued building out the pipes, securing them to the outside of the home. Our technician then sealed around the holes that had been drilled for the system. Now, the homeowner has a brand new radon system for their home! 

This homeowner in Vernon, CT called us out to their home to take a look at a potential mold issue and to replace old inefficient fiberglass insulation. Mold can be very dangerous. It is harmful to have in your home, especially for pets, young children, and older people. The old inefficient fiberglass without air sealing was also a huge concern. 

We removed all of the old, fiberglass insulation and properly disposed of the materials properly  Next, we fog our Mold-X treatment throughout the attic to neutralize any nooks and crannies that can be affected. Now we are ready for the next step. We seal up all top plates and any areas where air can escape from the home into the attic and be lost with foam. We even made an insulated storage area as shown in the after photo. Now we are ready to blow our Truoft Cellulose insulation into the attic. Cellulose will fill in any odd-shaped voids and gaps.

Now, thanks to Dr. Energy Saver by Eco Energy Solutions, this home is more energy efficient!

This homeowner in Vernon, CT called us hoping to get opinions regarding his home. He was hoping to talk about both attic and basement insulation. In the attic, he had old fiberglass batts. These were moldy, dirty, and needed to be replaced. 

We were able to help this customer! We were able to replace the attic insulation with TruSoft™ cellulose insulation. We started by removing the old blown-in insulation using a large vacuum. We then went in and air-sealed around all of the points where air leaks up from the home to the attic. We did this using our Zypfoam™ spray foam. Once the atitc is air sealed, we used a long hose to blow in TruSoft™ cellulose insulation. TruSoft™ is amazing -- it does not burn, get moldy, or attract pests. The blown-in insulation fills all gaps and oddly shaped voids. The homeowner is now much more comfortable in his home! 

This homeowner in Vernon, CT initially called us in the winter hoping for an audit to figure out how to make his home more energy efficient. He had recently moved in, and the home was very cold. Our Home Comfort Specialist came out and noted that, based off thermal imaging, his rim joist was completely uninsulated. However, this could not be confirmed due to the fact that the ceiling was covering it and would need to be cut back in order to check the insulation or re-insulate. The homeowner wanted to move forward, however, he knew that his work schedule would be very chaotic for a while. Therefore, he put the project on hold. He then called us back in the fall and said he was ready to move forward. 

We had the perfect solution for this customer! We first cut back the ceiling to ensure that we had accessed. We then insulated the rim joist (the perimeter of the floor framing system along the exterior of the home). We utilized two-part expanding spray foam. We spray this foam in the rim joist and over the sill plate. Insulating the rim joist in this way seals all air leaks - filling in the cracks and gaps that are present there. This prevents outside air from getting into the home. The homeowner is now very happy, and he is much more comfortable in his home! 

This homeowner in Wilbraham, MA had issues with freezing pipes and keeping their home warm. They had an insulated, but not quite effective door leading from hatch steps to the outside into the basement that was letting the cold in. There was a foil facing but the door was made of wood and was starting to splinter and deteriorate.

We started by removing the old door and frame. Once we installed updated framing, we installed our insulated door with weather stripping and a locking knob. Outside air will no longer be able to get in, meaning a warmer basement in the winter, and less humidity in the summer.

Thanks to Dr. Energy Saver by Eco Energy Solutions, pipes will no longer freeze and the homeowner will be more comfortable.