Chester, MA's Dependable Attic Insulation and Air Sealing Company!

This homeowner in Chester, MA called us looking for help with her insulation. She stated that she and her husband were tired of being extremely cold every winter. She stated that she was "freezing in her home". She had inadequate insulation in her attic and basement. In the basement, she had fiberglass batts in the ceiling. They were falling out and sagging, and were becoming more and more inefficient as time went on. 

We had the perfect solution for this customer! We utilized two-part expanding spray foam. Once we removed the old insulation, we insulated the rim joist (the perimeter of the floor framing system along the exterior of the home). We spray this foam in the rim joist and over the sill plate. Insulating the rim joist in this way seals all air leaks -- filling in the cracks and gaps that are present there. This prevents outside air from getting into the home. The homeowner is now very happy, and she is much more comfortable in her home!  

This homeowner in Chester, MA called us with concerns about his radon level. He had done some home tests, and they showed that the radon level was consistently between 25 and 30 pCi/L on average. He was very concerned about this and wanted a mitigation system installed as soon as possible.

We had the perfect solution for this customer! We installed a radon mitigation system in his home. We identified the specific space where the mitigation system should be installed. After that, we drilled a hole in the floor as well as a hole in the wall for the exterior penetration. We put together the pipes, starting in the floor, and built it out through the exterior penetration to the outside. We secured the pipes to the wall, and then installed the manometer onto the pipe. (A manometer measures the pressure of the radon gas in the system, indicating whether or not the system is functioning). We then went outside to continue building out the system. We installed the fan and continued building out the pipes, securing them to the outside of the home. Our technician then sealed around the holes that had been drilled for the system. Now, the homeowner has a brand new radon system for their home! 

This homeowner called Fogarty's Home Services looking for new insulation for his crawlspace. When our Home Comfort Specialist arrived, he noted that the insulation in the crawlspace was old, worn-out fiberglass insulation that had mold on it. The old thinking in crawl space construction was to vent the crawl space and create the thermal boundary (insulation layer) at the crawl space ceiling. It doesn’t work. Insulation is pulled by gravity away from the sub floor you’re supposed to be insulating. The same cold air under the insulation flows into the space on top of it - rendering the insulation useless. As the insulation gets heavier with moisture content, it falls away from the sub floor even more and can even fall to the floor. Fiberglass batt insulation has paper facing and organic material in the resin used to set the fibers into a batt - both are mold food. Results - mold, smelly insulation that is not providing any insulation value and has sagged or even fallen.

Before we could do anything else, we had to remove the old insulation. Fogarty's Home Services removed the existing fiberglass batts from the crawl space. It’s not fun laying on your back in a tight (dirt) crawl space. Insulation has hostile fibers when it’s disturbed. The insulation is very bulky and takes up a tremendous amount of space in trucks and our dumpsters which must be emptied. But it’s necessary to have a healthy home in the end. Result - now the crawl space is ready to be fixed properly with other solutions. No more nasty fiberglass insulation!

This homeowner in Chester, MA reached out to us looking for additional basement insulation. When our Home Comfort Specialist arrived at the home, he noted that they had insufficient basement insulation, including no insulation in the rim joist. The “rim joist” is the perimeter of the floor framing system along the exterior of the house. The joints and gaps between all the framing members allow for a lot of air leakage into the house. The rim joist is seldom insulated and never air sealed. Basement ceiling insulation, especially fiberglass batts, doesn’t stop the flow of cold air into the home. Results - cold floors, drafty, uncomfortable rooms, cold basement/lower level, higher heating and cooling bills and more condensation in the basement or crawl space in the summer.

Fogarty's Home Services was able to offer a solution to this customer -- sealing and insulating their rim joist with spray foam. Two part expanding spray foam is installed on rim joist and over sill plate to seal all air leaks from the outside and insulate this important area of the home. Our spray foam has a high insulation value per inch of R7, and because it expands, it seals all cracks and gaps and joints where air from the outside enters the home. Results - warmer floors, less drafts, more comfortable rooms, the house is easier to heat and costs less to heat, less summertime condensation on cold basement surfaces.

This homeowner in Chester, MA called us originally when they purchased a home with very little insulation. When our Home Comfort Specialist arrived in the home, he noted that, among other things, they needed new attic insulation. Since attics are vented, we should think of them thermally as outside in the winter. In summer because of the suns radiant heat, they are much worse than outside, reaching 130˚ on summer days. Clearly, we need to keep an absolute boundary between our living space and the attic so inside air doesn’t move to the attic in the heating season (convection), and heat doesn’t pass up through our ceilings in winter (conduction), and down from our ceilings in the hot summer (conduction, radiation). To reduce overall air leakage, the attic is the first priority because warm air rises to the top of the house and finds any and all holes to leak out into the cold vented attic and is lost. Holes, gaps and joints include between drywall and framing at the top of walls, around pipes, wires, electric boxes, fixtures, duct, penetrations, ceiling grilles and joints in framing. And the only reason cold air leaks in from the outside at the lower levels of the house, is that warm air leaked out of the top and created a suction at the bottom. Attics are dramatically under-insulated compared to today’s standards. Result - cold drafty rooms downstairs, colder floors, house is harder to heat and keep comfortable, higher fuel and electric bills.

Fogarty's Home Services had the perfect solution for this homeowner -- sealing the home and insulating using our TruSoft™ blown-in cellulose insulation. Adding insulation in an attic without sealing all air leaks first should never be done, because you are burying air leaks and making them impossible to seal later - and insulation DOES NOT STOP air leaks. That’s why we first carefully air seal the many various points where air from your home leaks up into your attic and is lost. We use expanding foam, boards, caulk, and metal flashing and fire caulk around your masonry or metal chimney as appropriate. If necessary, baffles (air chutes) are installed in each rafter bay to keep soffit vents clear and prepare for insulation. Finally, our premium TruSoft™ cellulose insulation is blown to the optimum R-value (typically R60). TruSoft™ will not burn, get moldy, or attract pests. Blown insulation fills all gaps and odd shaped voids, and by filling over framing members, “thermal bridging” is avoided. Results - a warmer, more comfortable, less drafty house that you’ll notice everywhere - even downstairs! House is quieter. Fuel and electric bills are lower.