Reliable Insulation & Radon Testing Company in Scotland, CT

This homeowner in Scotland, CT called us hoping we would be able to help him insulate his walls after a remodel revealed that they did not have proper insulation. Many older homes have no insulation in the exterior walls. This causes obvious problems. Heat flows from more (inside) to less (outside in winter) right through the walls, and the opposite in summer. Nearly all walls leak air, insulated or not, causing drafts. The cold wall surface cools interior air which then sinks and travels across the floor and up the warmer interior wall, and across the ceiling back to the exterior wall. This is called a "convective loop" and makes rooms feel even draftier. Results - cold, drafty rooms, uncomfortable home, heating and cooling systems run much more and need more service, difficult to keep house at comfortable temperature, higher fuel and electric bills, dry home in winter, more dust/pollen, more humidity in the house in summer when air conditioned.

We had the perfect solution for this homeowner. In this solution, the siding is removed temporarily as necessary and 2 9/16" holes are drilled through the wall sheathing. A fill tube is inserted up (and down) into wall cavities to not only fill, but dense pack the wall cavities. Dense packing is a technique that packs the insulation in very tightly - so tightly that all irregular shaped cavities and crevices in the wall cavities are filled, and air will not penetrate the dense packed cellulose. It's remarkable, and something that can't be achieved with fiberglass - not even close! Dense packed cellulose stops air flow through the wall and insulates. TruSoft™ Cellulose is treated to be highly fire, mold and pest resistant. Holes are plugged and siding is put back. Results - a less drafty, warmer, quieter, more comfortable house, less dust/pollen, house not so dry in winter, lower fuel/electric bills, heating system runs - less maintenance. 

This homeowner in Scotland, CT reached out to us looking for information on the efficacy of spray foam insulation in a basement compared to fiberglass insulation. He was looking to re-insulate his basement. In a basement, the “rim joist” is the perimeter of the floor framing system along the exterior of the house. The joints and gaps between all the framing members allow for a lot of air leakage into the house. The rim joist is seldom insulated and never air sealed. Basement ceiling insulation, especially fiberglass batts, doesn’t stop the flow of cold air into the home. Results - cold floors, drafty, uncomfortable rooms, cold basement/lower level, higher heating and cooling bills and more condensation in the basement or crawl space in the summer.

We had the perfect solution for this homeowner. In this solution, we spray foam the rim joist in the basement in order to seal and insulate it. Two part expanding spray foam is installed on the rim joist and over the sill plate to seal all air leaks from the outside and insulate this important area of the home. Our spray foam has a high insulation value per inch of R7, and because it expands, it seals all cracks and gaps and joints where air from the outside enters the home. Results - warmer floors, less drafts, more comfortable rooms, the house is easier to heat and costs less to heat, less summertime condensation on cold basement surfaces.

This homeowner in Scotland, CT called us hoping that we would be able to help him and his mother insulate their home. They had gotten an energy audit from Eversource that identified several problems with their insulation in their attic, basement, and walls. Since attics are vented, we should think of them thermally as outside in the winter. In summer because of the suns radiant heat, they are much worse than outside, reaching 130˚ on summer days. Clearly, we need to keep an absolute boundary between our living space and the attic so inside air doesn’t move to the attic in the heating season (convection), and heat doesn’t pass up through our ceilings in winter (conduction), and down from our ceilings in the hot summer (conduction, radiation). To reduce overall air leakage, the attic is the first priority because warm air rises to the top of the house and finds any and all holes to leak out into the cold vented attic and is lost. Holes, gaps and joints include between drywall and framing at the top of walls, around pipes, wires, electric boxes, fixtures, duct, penetrations, ceiling grilles and joints in framing. And the only reason cold air leaks in from the outside at the lower levels of the house, is that warm air leaked out of the top and created a suction at the bottom. 

We had the perfect solution for this homeowner. Adding insulation in an attic without sealing all air leaks first should never be done, because it is just burying air leaks and making them impossible to seal later - and insulation DOES NOT STOP air leaks. That’s why, in this solution, we first carefully air seal the many various points where air from the home leaks up into the attic and is lost. Our premium TruSoft™ cellulose insulation is blown to the optimum R-value (typically R60). TruSoft™ will not burn, get moldy, or attract pests. Blown insulation fills all gaps and odd shaped voids, and by filling over framing members, “thermal bridging” is avoided.