Haydenville, MA's Trusted Home Insulation & Mold Remediation Company

This homeowner in Haydenville, MA called us hoping that we would be able to help them with their attic insulation. They had very temperature sensitive rooms, and they believed that the issue may be air leaks in the attic. Since attics are vented, we should think of them thermally as outside in the winter. In summer because of the suns radiant heat, they are much worse than outside, reaching 130˚ on summer days. Clearly, we need to keep an absolute boundary between our living space and the attic so inside air doesn’t move to the attic in the heating season (convection), and heat doesn’t pass up through our ceilings in winter (conduction), and down from our ceilings in the hot summer (conduction, radiation). To reduce overall air leakage, the attic is the first priority because warm air rises to the top of the house and finds any and all holes to leak out into the cold vented attic and is lost. Holes, gaps and joints include between drywall and framing at the top of walls, around pipes, wires, electric boxes, fixtures, duct, penetrations, ceiling grilles and joints in framing. And the only reason cold air leaks in from the outside at the lower levels of the house, is that warm air leaked out of the top and created a suction at the bottom. Attics are dramatically under insulated compared to today’s standards. Result - cold drafty rooms downstairs, colder floors, house is harder to heat and keep comfortable, higher fuel and electric bills.

We had the perfect solution for this homeowner. Adding insulation in an attic without sealing all air leaks first should never be done, because it is just burying air leaks and making them impossible to seal later - and insulation DOES NOT STOP air leaks. That’s why, in this solution, we first carefully air seal the many various points where air from the home leaks up into the attic and is lost. Our premium TruSoft™ cellulose insulation is blown to the optimum R-value (typically R60). TruSoft™ will not burn, get moldy, or attract pests. Blown insulation fills all gaps and odd shaped voids, and by filling over framing members, “thermal bridging” is avoided. Results - a warmer, more comfortable, less drafty house that the homeowner notice everywhere - even downstairs! House is quieter. Fuel and electric bills are lower.

This homeowner in Haydenville, MA called us hoping that we would be able to help him with his home's insulation. He had no insulation in the basement. In a basement, the “rim joist” is the perimeter of the floor framing system along the exterior of the house. The joints and gaps between all the framing members allow for a lot of air leakage into the house. The rim joist is seldom insulated and never air sealed. Basement ceiling insulation, especially fiberglass batts, doesn’t stop the flow of cold air into the home. Results - cold floors, drafty, uncomfortable rooms, cold basement/lower level, higher heating and cooling bills and more condensation in the basement or crawl space in the summer.

We had the perfect solution for this customer. In this solution, we spray foam the rim joist in the basement in order to seal and insulate it. Two part expanding spray foam is installed on the rim joist and over the sill plate to seal all air leaks from the outside and insulate this important area of the home. Our spray foam has a high insulation value per inch of R7, and because it expands, it seals all cracks and gaps and joints where air from the outside enters the home. Results - warmer floors, less drafts, more comfortable rooms, the house is easier to heat and costs less to heat, less summertime condensation on cold basement surfaces.

This homeowner in Haydenville, MA called us hoping that we would be able to help him. They were having a moisture problem in the home, which turned out to be from high humidity. High humidity in a basement is caused by a number of important conditions. High humidity causes many problems in a home such as mold (which grows at Relative Humidities [RH] above 75%), rot (which happens above 90% RH) odors, airborne mold spores that aggravate allergies and asthma, increased pests and insects such as termites, and higher air conditioning and heating costs. Result - cold floors above, condensation, mold, rot, odors, drafty, uncomfortable home, higher fuel and electric bills.

We had the perfect solution for this customer. The SaniDry™ Sedona air system is a powerful but energy efficient dehumidification and air filtration system in one unit. Able to remove an incredible 100 pints of water per day and using only 5.9 amps of electricity, the SaniDry™ Sedona drains automatically to a sump or the outside with a condensate pump. It has a powerful 310 cfm blower to circulate the dry air completely around to dry building materials and contents. Mold doesn’t have a chance! An automatic control is easy - set it to 55% RH and forget it - the SaniDry™ Sedona does the rest! And there’s no buckets to empty! Results - Low Relative Humidity, mold stops growing, odors are reduced, basement is suitable for storage, lower air conditioning cost, upstairs is dryer.