Trusted Radon Testing & Mitigation Company in New Britain, CT

This homeowner in New Britain, CT approached us at a home show hoping we would be able to help him with his attic. He had a small amount of blown in insulation, but wanted an attic evaluation since it was not as high as it should be. Since attics are vented, we should think of them thermally as outside in the winter. In summer because of the suns radiant heat, they are much worse than outside, reaching 130˚ on summer days. Clearly, we need to keep an absolute boundary between our living space and the attic so inside air doesn’t move to the attic in the heating season (convection), and heat doesn’t pass up through our ceilings in winter (conduction), and down from our ceilings in the hot summer (conduction, radiation). To reduce overall air leakage, the attic is the first priority because warm air rises to the top of the house and finds any and all holes to leak out into the cold vented attic and is lost. Holes, gaps and joints include between drywall and framing at the top of walls, around pipes, wires, electric boxes, fixtures, duct, penetrations, ceiling grilles and joints in framing. And the only reason cold air leaks in from the outside at the lower levels of the house, is that warm air leaked out of the top and created a suction at the bottom. 

We had the perfect solution for this homeowner. Adding insulation in an attic without sealing all air leaks first should never be done, because it is just burying air leaks and making them impossible to seal later - and insulation DOES NOT STOP air leaks. That’s why, in this solution, we first carefully air seal the many various points where air from the home leaks up into the attic and is lost. Our premium TruSoft™ cellulose insulation is blown to the optimum R-value (typically R60). TruSoft™ will not burn, get moldy, or attract pests. Blown insulation fills all gaps and odd shaped voids, and by filling over framing members, “thermal bridging” is avoided.

This homeowner in New Britain, CT reached out to us saying that she has issues with water in her basement. She had two sump pumps that were not adequately doing the job. A sump pump is a critically important part of a home because it keeps an entire level of the home protected against flooding - which could cause many thousands of dollars in property damage, clean up time and aggravation. Results -- A flooded basement, mess, property damage, and mold -- just what this homeowner was trying to avoid! 

Luckily, Fogarty's Home Services had the perfect solution for this customer -- the TripleSafe™ sump pump system. The TripleSafe™ system has 3 pumps to protect from flooding. The first pump is a 1/3 hp, cast iron Zoeller pump that can pump up to 2200 gallons per hour, 8 feet high. Should the first pump fail or not be able to keep up with the temporary heavy flow of water, a 1/2 hp AC back-up pump on a separate discharge line can pump 3900 gallons of water per hour. If the power fails, then a third, battery operated "UltraSump" pump automatically pumps up to 12,000 gallons of water out of the basement! An airtight lid keeps moisture, odors and radon gas out of the basement. The TripleSafe™ system is the highest quality sump pump protection in the world! Results -- the homeowner has peace of mind knowing she has both AC and DC powered back up pumps to keep her basement dry. 

This homeowner in New Britain, CT called us saying that she was having an issue with water and high humidity in her basement. High humidity in a basement is caused by a number of important conditions. High humidity causes many problems in a home such as mold (which grows at Relative Humidities [RH] above 75%), rot (which happens above 90% RH) odors, airborne mold spores that aggravate allergies and asthma, increased pests and insects such as termites, and higher air conditioning and heating costs. Result - cold floors above, condensation, mold, rot, odors, drafty, uncomfortable home, higher fuel and electric bills.

We had the perfect solution for this customer. The SaniDry™ Sedona air system is a powerful but energy efficient dehumidification and air filtration system in one unit. Able to remove an incredible 100 pints of water per day and using only 5.9 amps of electricity, the SaniDry™ Sedona drains automatically to a sump or the outside with a condensate pump. It has a powerful 310 cfm blower to circulate the dry air completely around to dry building materials and contents. Mold doesn’t have a chance! An automatic control is easy - set it to 55% RH and forget it - the SaniDry™ Sedona does the rest! And there’s no buckets to empty! Results - Low Relative Humidity, mold stops growing, odors are reduced, basement is suitable for storage, lower air conditioning cost, upstairs is dryer.